牵引车载荷对NOx排放和排温影响的试验研究

在五轴动力总成试验台架上对牵引车在不同载荷下进行同一路谱的排放试验,研究牵引车在不同载荷下NOx排放和排温的变化,得到载荷与排放物和选择性催化还原(selective catalytic reduction,SCR)上游排温的变化关系。结果表明:载荷为标定载荷的60%以下时,NOx比排放值与载荷基本呈线性相关;载荷超过标定载荷的75%时,NOx比排放值与载荷呈二次项相关;载荷在为标定载荷的23%以上时,NOx比排放值与SCR上游排温基本呈线性相关。利用该试验结论可以通过只进行单一载荷排放试验,判断车辆在其他载荷下的排放水平是否满足国家标准要求,并可通过载荷对排温的影响规律预判排放水平。     

ASME Ⅱ卷D篇表U数据作为设计校核中材料验收标准存在问题及探讨

ASME标准钢板对于短时高温抗拉数据无规定,但设备设计人员在校核时又要用到此数据,于是有些设计文件在技术要求中将ASME II卷表U的数据作为材料验收的标准。针对此种做法引发的争议及涉及的主要问题进行试验验证和分析探讨。研究结果表明,ASME II卷D篇表U中的数据是基于室温抗拉强度保证值,并根据拟合曲线将室温保证值提高了10%得到的,实测数据与ASME规范数据不一致,部分材料在250~350℃存在动态应变时效现象,但仍不满足设计要求。材料经模拟焊后热处理后性能下降,难以到达交货态的要求。给出了短时高温抗拉强度的选用建议。     

浅谈不同给液方式在铜电解车间的应用

不同给液方式对铜电解过程中有重要的影响,不同的循环方式会影响槽内温度分布、电解液成分及阳极泥沉降等,因此,根据铜电解生产不同情况的需要,分析对比了多种给液方式在贵冶电解车间的应用,总结了这几种给液方式的优缺点和适用条件。     

一种压电半导体纳米线的热电耦合性能研究

采用有限元分析方法,研究了一种n型压电半导体纳米线(氧化锌)的电热耦合性能,分析了外部温度对氧化锌纳米线内部机械场、电场及电流场分布的影响,并讨论了本构方程线性化对电学参数的影响。研究结果表明,温度对氧化锌纳米线的电场、载流子浓度和电流密度影响很大,采用线性本构和非线性本构求得的电场、电子浓度和电流密度最大相差分别为24%,32%和68%,基于非线性本构分析压电半导体的电学性能会引起很大误差。该研究结果可为压电半导体器件利用温度调控电场、电流提供理论依据。     

Effect of high temperature and separated combustion on SO2 release characteristics during coal combustion under O2/CO2 atmosphere

This paper studied the effect of high temperature (up to 1873K) and separated combustion mode (volatile combustion and char combustion are separated) on SO₂ release characteristics during pulverized coal combustion under O₂/CO₂ atmosphere. Coal combustion experiments were conducted at different combustion environment temperatures utilizing a high temperature fixed-bed setup. The results show that as temperature rises, the SO₂ release curve is transformed from a single-peak process to a double-peak process. In separated combustion, temperature has little effect on the volatile-SO₂ (SO₂ released during volatile combustion) but brings about a significant effect on char-SO₂ (SO₂ released during char combustion). Char-SO₂ release amount and the ratio of it to fuel-SO₂ release amount (total SO₂ released during coal combustion) increase with temperature rising. The increase of temperature leads to a dramatic decreasing of sulphur mass fixed in the ash and causes SO₂ release amount to rise when temperature is lower than 1573 K. Separated combustion causes a higher SO₂ release amount than coupled combustion (the same as conventional combustion, volatile combustion and char combustion are simultaneous). Thermochemistry equilibrium composition calculation results show that alkali metals and alkaline-earth metals are significant in sulphur retention. CaSO₄ and Na₂SO₄ are the main sulphates at high temperatures.     

Improved one-dimensional beam model for unbalanced composite single-lap joint

An analytical nonlinear solution was provided for unbalanced composite single-lap joint (CSLJ) using an improved one-dimensional beam model, which incorporated the effect of bending–tension coupling. The bending–tension coupling stiffness was introduced to characterize the coupling bending and tension behavior induced by the un-symmetric stacking sequence of composite laminates. The governing differential equations captured the bending–tension coupling behavior and the geometrically nonlinear features were constructed based on the displacement compatibility conditions of flexible interface. The transverse deformation in overlap region, edge moment factors and adhesive stress distributions for the unbalanced CSLJ with inflexible, intermediate flexibility and flexible adhesive can be determined by the present one-dimensional beam model. The accuracy of the present model was validated by the comparison with nonlinear finite element model. The effect of bending–tension coupling on edge moment factors and peak values of adhesive stresses was shed light on with the present model.     

铅锌多金属矿分段浓缩选别技术的研究与应用

通过多碎细磨、原矿分级溢流优先浓缩脱水,进行了高浓度选铅银、选锌,锌尾矿再浓缩脱水选硫、选锰,同时匹配合理的选矿药剂,原矿浓缩水回用于磨矿分级和选铅,锌尾浓缩水回用于选锌,尾矿浓缩水回用于选硫、选锰,剩余各种废水经适度处理回用于选铅和磨矿分级等,使一段磨矿细度-74μm从70%提高到80%,铅、锌、硫入选初始浓度分别提高到50%、40%、50%,选矿废水全部分质回用。铅锌硫银回收率分别提高了1.5、2.83、13.57、1.01个百分点,硫精矿主品位从38.9%提高到46.5%,设备减少40%、能耗降低25%,节约了选矿药剂消耗和废水处理费用,实现了铅锌多金属矿产资源的高效回收和节能环保。     

退火温度对0Cr25Al5热轧态盘条钢组织及性能的影响

采用显微组织分析和分子动力学模拟等方法研究了退火温度对0Cr25Al5热轧态盘条钢组织及性能的影响。结果发现,晶粒尺寸随温度的升高逐渐增加并趋于稳定,但是断后伸长率和断面收缩率在950 ℃突然大幅度下降。试样组织形貌在800 ℃和950 ℃退火温度下的OM及SEM分析结果未见明显差别。于是使用分子动力学模拟对0Cr25Al5钢三元体系的自由能进行了计算,发现随着B2结构的FeAl或者DO3结构的Fe₃Al有序相尺寸的增大,系统自由能先减小后增大,其最小值随着退火温度的升高向有序相颗粒尺寸减小的方向移动。在1273 K的高温下仍然会保留60 nm左右大小的有序相颗粒。因此,推测0Cr25Al5钢在大于950 ℃的温度范围内韧性下降是由于60 nm左右的B2结构的FeAl或者DO3结构的Fe₃Al有序相造成,与晶粒尺寸无关。因此,针对该钢种应进行低温退火促使基体组织回复以消除缺陷,从而抑制Fe、Al等基体原子的扩散。     

基于α-FeOOH催化H2O2蒸气的低温烟气脱硝实验

针铁矿是分布广泛、储量丰富的铁氧化物，其主要成分为α-羟基氧化铁（α-FeOOH）。为了探究针铁矿在催化H₂O₂烟气脱硝反应中的性能，本文通过沉淀-水解法制备了α-FeOOH，并在自行搭建的实验台上开展了α-FeOOH催化H₂O₂的低温烟气脱硝实验研究，深入分析了H₂O₂流量、H₂O₂浓度、汽化温度、反应温度和共存气体浓度等工况参数对脱硝性能的影响。采用离子色谱（IC）分析了单独脱硝反应和同时脱硫脱硝反应后的含氧酸成分，结合各项表征分析技术考察了催化剂反应前后的理化特性和稳定性。实验结果显示，随着汽化温度和反应温度的升高，NO的脱除效率先增加后降低；增加H₂O₂浓度对脱硝效率有明显的促进作用。当汽化温度为140℃、反应温度为160℃时，以2.5mL/h注入10mol/L的H₂O₂脱硝效率达到80%。当SO₂浓度为1000μL/L时，脱硝效率提高至86.4%。离子色谱分析结果显示，单独脱硝反应和同时脱硫脱硝反应后含氧酸产物为HNO₃和H₂SO₄。反应前后催化剂的表征结果显示，α-FeOOH在脱硝反应后依然具有良好的稳定性，显示出针铁矿在低温烟气脱硝工艺中的潜在应用前景。     

Effect of clad ratio on interfacial microstructure and properties of cladding billets via direct-chill casting process

Numerical simulation and experiments were introduced to develop AA4045/AA3003 cladding billets with different clad-ratios. The temperature fields, microstructures and mechanical properties near interface were investigated in detail. The results show that cladding billets with different clad-ratios were fabricated successfully. Si and Mn elements diffused across the bonding interface and formed diffusion layer. With the increase of clad-layer thickness, the interfacial region transforms from semisolid–solid state to liquid–solid state and the diffusion layer increased from 10 to 25 μm. The hardness at interface is higher than that of AA3003 side but lower than that of the other side. The bonding strength increased with the clad-layer thickness, attributing to solution strengthening due to elements diffusion. The cladding billets were extruded into clad pipe by indirect extrusion process after homogenization. The clad pipe remained the interfacial characteristics of as-cast cladding billet and the heredity of clad-ratio during deformation was testified.